Academia.edu no longer supports Internet Explorer.
To browse Academia.edu and the wider internet faster and more securely, please take a few seconds to upgrade your browser .
Enter the email address you signed up with and we'll email you a reset link.
- We're Hiring!
- Help Center
Experimental Determination of Planck's constant using Light Emitting Diodes (LEDs) and Photoelectric Effect
Related Papers
Journal of Physics: Conference Series
Aniello Saggese
In recent years, Modern Physics has been included in the curricula of Italian secondary schools, so that many teachers are asking for specific didactical tools to allow their students to acquire the right skills to deal with final examinations. The Physics Department at University of Salerno (Italy) is, therefore, planning PLS (Piano Lauree Scientifiche / Scientific Degree Project) training courses to give some valid educational paths through new didactical strategies for Physics learning. Introducing quantum mechanics by experimental set-ups with commonly used materials is a rather interesting and challenging task. In fact, this practice allows teacher attending the course to reproduce the same experiments in their own class. Moreover, by using readily available material for the experimental set-up, a soft approach to Modern Physics can be achieved. In the present work, we propose the analysis of an experiment: the measurement of Planck’s constant, one of the most important fundame...
francesca santonocito
Experimental determination of Planck's constant h = 6:6261034J s is performed using Light Emitting Diodes (LEDs). Spectropho- tometry and basic circuit analysis techniques are employed to obtain empirical data with respect to the energy of the emitted photons of light and thus used to calculated Planck's constant. It is found using three LEDs of di erent colors that the experimental value observed is 6:180 1034J s with a = 3:092 1036.
Belachew Desalegn
When light is incident on certain metallic surfaces, electrons are emitted from the surface–This is called the photoelectric effect–The emitted electrons are called photoelectrons. The successful explanation which enabled the first convincing experimental verification of quantum theory had been provided by Einstein. In this article, light of a known frequency is assumed to shine upon the alkali metallic surface (potassium) acting as the photocathode in an evacuated tube. The photocathode is irradiated by light of approximately only one wavelength or colour (quasi-monochromatic light), and a voltage is applied between the anode (where the current is measured) and cathode so that it opposes the energy of the emitted photoelectrons. The potential energy gained (or kinetic energy lost) is <em>eV </em>where <em>e </em>is the charge of the electron and <em>V </em>is the potential difference or voltage between the anode and cathode. The voltage required ...
Andrew D Miller
Utilising the properties of certain alkali metals and the particle-like properties of light, the photoelectric effect can be used to estimate the value of the fundamental constant h. A high pressure mercury lamp was directed onto a photocell through a series of lenses and spectral filters, and a small photocurrent was observed at specific frequencies. Applying a range of opposing voltages to the photocell caused the photocurrent to drop to zero, and plotting these voltages against the corresponding frequencies meant Planck's constant could be evaluated. Using three different methods of determine h, an average value of (6.17 ± 0.68) × 10 −34 Js was calculated.
Latin American Journal of Physics Education
Natural Science and Advanced Technology Education
Riste Popeski Dimovski
This is the problem of the 8th International Experimental Physics Olympiad (EPO8). The task of the EPO8 is to determine Planck constant ħh/2 using the given set-up with LED. If you have an idea how to do it, do it and send us the result; skip the reading of the detailed step by step instructions with increasing difficulties. We expect the participants to follow the suggested items – they are instructive for physics education in general. Only the reading of historical remarks given in the first section can be omitted during the Olympiad without loss of generality. Participants should try solving as much tasks as they can without paying attention to the age categories: give your best.
Jonathan N . Muchuma
There are six different types of Light-Emitting Diodes commonly used to determine the value of 'Plank's Constant', a most essential constant in modern-day physics. Using Microsoft Excel for computational purposes, significant subtleties were observed during analysis of the interrelationships between Current, Voltage, Photon Energy, and Frequency which will be detailed in this report.
Jurnal Pendidikan Fisika
Ana Dhiqfaini Sultan
The photoelectric effect experiment generally uses a very sophisticated and expensive apparatus. Some high schools and even universities in Indonesia cannot afford to conduct this experiment because of the high price of the apparatus. The purpose of this study was to develop a user-friendly, and cost-effective teaching aids which can be used to demonstrate the concepts of modern physics related to the photoelectric effect. The stages of this study employed the Four-D model, namely define, design, develop, and disseminate. Based on experts and practitioner evaluation, the developed teaching aids and practicum devices of photoelectric effect experiment were found to be valid and reliable. The results of the experiment by using this developed teaching aids of the photoelectric effect showed that there is a linear relationship between the stopping potential and the frequency of light emitted by the LED. These results are consistent with…
Journal of physics
Marisa Michelini
Loading Preview
Sorry, preview is currently unavailable. You can download the paper by clicking the button above.
RELATED PAPERS
George Kalkanis
COLLASE (Creative of Learning Students Elementary Education)
rina martha riani
MARIA ROSARIA DEL SORBO
VELONAKIS IOANNIS
Science & Education
Stephen Klassen
Journal of Chemical Education
Elias Faraclas
CLAUDIA DANIELA CZIPROK
Arnaud Mayrargue
12th Education and Training in Optics and Photonics Conference
Paulo Varela
Rini Oktavia
vincenzo cioci
Journal of Baltic Science Education
Peter Demkanin
ICERI Proceedings
Maurizio Zani
Don Metz , Mansoor Niaz , Sarah Dietrich
Batman returns
PROPOSAL FOR A POTENTIALLY SIGNIFICANT TEACHING UNIT (UEPS) FOR TEACHING MODERN PHYSICS TO HIGH SCHOOL STUDENTS: THE CORPUSCULAR NATURE OF LIGHT AND ITS APPLICATIONS (Atena Editora)
Atena Editora
Marlise Geller
Fifteenth Conference on Education and Training in Optics and Photonics: ETOP 2019
Alberto Tufaile
Science Education
David Hammer
Petre Ogrutan , Lia Elena Aciu
wengluck cheang
- We're Hiring!
- Help Center
- Find new research papers in:
- Health Sciences
- Earth Sciences
- Cognitive Science
- Mathematics
- Computer Science
- Academia ©2024
All Lab Experiments
To Determine the V-I Characteristics of an LED and Calculate the Wavelength of the Emitted Light “OR” Determination of Planck’s Constant using LED
- Electromagnetic Theory
- Physics Practical Files
Here is the Experimental File in pdf format.
If you want to determine the value of Planck’s Constant using LED. Here is just a little modification in the calculations. Rest experiment is the same.
Find more Electromagnetic Theory related Practicals in this Link – https://alllabexperiments.com/phy_pract_files/emt/
Watch “How to perform this Experiment” in this video – https://www.youtube.com/watch?v=9eeHoErba0Q
Watch “Most Important Viva Questions” on LED and Planck’s Constant – https://www.youtube.com/watch?v=vLgI7uEDVXg
2 thoughts on “To Determine the V-I Characteristics of an LED and Calculate the Wavelength of the Emitted Light “OR” Determination of Planck’s Constant using LED”
What will be the change in to determine the value of planks constant using LED ?
In that case, no calculation, and you only observe V-I values for LED in forward and reverse bias.
Leave a Reply Cancel reply
Your email address will not be published. Required fields are marked *
Save my name, email, and website in this browser for the next time I comment.
Related Posts
Bas-107 – preliminary experiment write up – igdtuw (write only first three not forth).
This post contains the writing material for preliminary experiments to be written in lab practical file by IGDTUW sem-II engineering ...
To Determine Specific Charge (e/m) of an Electron using Thomson Method – Practical File with Reading
This pdf file contains the lab manual of ebym experiment using Thomson method with Observation Table and Reading. ...
To Determine the Coefficient of Thermal Conductivity of a Bad Conductor by Lee’s and Charlton’s Method
Find the pdf file of this experiment and other useful video links related to this experiment. ...
Experimental Determination of Planck’s constant using Light Emitting Diodes (LEDs) and Photoelectric...
Andrea Checchetti, Alessandro Fantini
Science and Education Publishing
From Scientific Research to Knowledge
- Browse by Subjects
- Journal Home
- For Authors
- Online Submission
- Current Issue
Experimental Determination of Planck’s constant using Light Emitting Diodes (LEDs) and Photoelectric Effect
1 Istituto d'Istruzione Superiore "Leonardo da Vinci"
2 Liceo Scientifico "E. Fermi" Catanzaro Lido
- Related Content
- About the Authors
- Follow the Authors
1. | |
2. | |
3. | |
4. | |
5. | |
The aim of this experiment was to utilize the Inquiry Based Science Education, (IBSE) in order to offer the students a better understanding of the light-matter interaction. The inquiry-based teaching addresses the question of how the students make observations, develop hypotheses about phenomena, and devise tests to investigate their hypotheses. Using IBSE they share responsibility within the group for what concerns answering questions, and use a scientific approach to solve problems. 4 th year students of undergraduate degree program of an Italian Arts Lyceum and 5 th year students of undergraduate degree program of an Italian Scientific Lyceum have experimentally determined the value of Planck's constant, h . They have used respectively two methods: a) current-voltage measurements of a series of different colored LEDs; b) a method based upon the comparison of the incident light beams values of potential arrest with different wavelength on a photo emissive surface, using the photoelectric effect through an apparatus built on an optical bench. This work is an essential part of an apprenticeship developed during the “Professione Formatore in Didattica delle Scienze” Master, which takes place at the University of Calabria, with the authors taking part in it as trainees and that will be over in the month of October 2015.
Keywords: IBSE (Inquiry-Based Science Education), planck’s constant, LEDs (Light-emitting diodes), photoelectric effect
Received July 10, 2015; Revised August 03, 2015; Accepted August 06, 2015
Cite this article:
- Normal Style
- Chicago Style
- Andrea Checchetti, Alessandro Fantini. Experimental Determination of Planck’s constant using Light Emitting Diodes (LEDs) and Photoelectric Effect. World Journal of Chemical Education . Vol. 3, No. 4, 2015, pp 87-92. https://pubs.sciepub.com/wjce/3/4/2
- Checchetti, Andrea, and Alessandro Fantini. "Experimental Determination of Planck’s constant using Light Emitting Diodes (LEDs) and Photoelectric Effect." World Journal of Chemical Education 3.4 (2015): 87-92.
- Checchetti, A. , & Fantini, A. (2015). Experimental Determination of Planck’s constant using Light Emitting Diodes (LEDs) and Photoelectric Effect. World Journal of Chemical Education , 3 (4), 87-92.
- Checchetti, Andrea, and Alessandro Fantini. "Experimental Determination of Planck’s constant using Light Emitting Diodes (LEDs) and Photoelectric Effect." World Journal of Chemical Education 3, no. 4 (2015): 87-92.
At a glance: Figures
View all figures
1. Introduction
The interaction of light and matter is synthetically expressed by Einstein-Planck equation:
(1) |
where the constant of proportionality h has the following value:
It represents a milestone in the introduction to quantum mechanics; also known as “quantum of energy” or “quantum of action”. It is one of the fundamental physics constants, useful to understand the meaning of quantization in the atomic and nuclear world and represents the fundamental unit of action for discrete atomic scale system; it defines the minimum amount for the light energy and the electrons’ energies in atoms. Understand its physical meaning is the first step to bring students closer to the concept of quantization of energy, the starting point of a historical-didactic route that has as successive steps the wave nature of the electron, the uncertainty principle, the Schrödinger equation, until trace the development of the atomic structure. Light, quanta and Planck's constant are concepts that embrace both the chemistry that the physics.
The value of h was performed using Light Emitting Diodes (LEDs) and photoelectric effect.
In the Light Emitting Diodes (LEDs) method’s, we first make a complete circuit, using various apparatus (Figure 1). We use four colors (red, yellow, green and blue) for the different LEDs in the first place, to derive the voltage-current characteristic curves using the same circuit (Figure 3).
Then we use the linear part of voltage-current characteristic curves to estimate the slope (m) and intercept (n) corresponding to each LEDs (e.g., Figure 7 shows the red LED). These values are used to estimate V g for different color LEDs, the potential that corresponds to the voltage for which the electrons are able to recombine with “holes” of the valence band. The Planck’s constant corresponding to each color is then determined using equation (3), whose values are presented in Table 2 .
In the Photoelectric Effect method’s, light of a known frequency is allowed to fall on a metal photoemission surface acting as the photocathode (emitter plate in Fig. 6). Electrons are ejected from the cathode and some reach the collector producing a photoelectric current (Fig. 6).
The anode can be made negative (reverse bias) with respect to the cathode to repel the electrons. Only electrons leaving the emitter surface with initial kinetic energy greater than the potential energy between the cathode and collector will reach the anode and register a current. The potential difference can be increased until no electrons reach the collector and the current is stopped. This potential is called the stopping potential V a (eq. 6).
The above operation is repeated for two different radiations (incident light with differing frequencies) so that h can be estimated using equation 7.
The Planck’s constant value has been determined by using, under the educational profile, the same methodology: the Inquiry Based Science Education, (IBSE).
IBSE is a useful process that allows:
• Creation or choice of activities that motivate and involve students
• Determination of learning outcomes and appropriate assessment methods
• Use of specialized tools and digital technology
• Selection of educational resources, such as reading materials and useful websites
The teaching based on the research addresses the matter of how students make observations, how they develop hypotheses about the phenomena and how they can anticipate tests to investigate their hypothesis.
The inquiry process involved the following steps [ 1 ] :
1) Engagement
4) Elaborate
5) Evaluate
For each of the experimental methods used by the authors to calculate the Planck constant, the following Learning Activities have been developed:
LIGHT EMITTING DIODES (LEDS) METHOD
1 st Learning Activity (Developing the concept so that the students can gain an appreciation of the following)
The diode LED, as all the diodes, is a semiconductor device, which behaves as a bulb lighting up when connected to a voltage generator. The radiated energy can derive experimentally from the characteristic curve of the diode. Therefore, it can be easily seen that each LED is a "non-ohmic conductor", because the voltage-current relation does not follow Ohm's law of direct proportionality.
2 nd Learning Activity (Hypothesis and Experiment Design)
When an electron and a hole meet, they recombine and generate a photon; electrical energy of the couple is transformed in the electromagnetic energy of the photon.
• Discuss with the students about experiment design.
• Identify the tools needed to get the current-voltage curves.
• Building the circuit.
3 rd Learning Activity (Experiment activity)
Measure the threshold voltage for different color LEDs:
• Acquisition of the measures: varying the supply voltage of the circuit the students will measure the function of V diode .
• To plot the trend of the current as a function of the potential difference.
• Fit for the linear part of the curve of the four LEDs we used, I = mV - n. If I = 0 one obtains V threshold .
4 th Learning Activity (Discussion and conclusion)
• The students drawn the characteristic curve of dyed LEDs and using Excel determine the equation of the linear part;
• With the calculation performed with Excel software, the students can determine the experimental value of Planck's constant.
• For each value of h the student calculates the percentage error.
• The light emission of the LED starts from a value of potential (V g ) that corresponds to the voltage for which the electrons are able to recombine with “holes” of the valence band. Experimentally, in order to determine the value of this potential the students proceed with an extrapolation of the linear part of the intensity curve of the current-voltage until it meets the x-axis.
• The value given by the intersection represents the voltage value, which multiplied by the electron charge gives us the amount of the energy of the emitted photons.
• Compare the experimental value of h with that of the literature.
PHOTOELECTRIC EFFECT METHOD
1 st Learning Activity (Developing the concept in order that students can gain an appreciation of the following)
A Hg vapor lamp emits monochromatic light, exploiting the potential of an optical bench, passes through filters of different wavelength and strikes a photo emissive surface K. Also interesting is to note that the incident light is transformed into electricity.
2 nd Learning Activity (Hypotheses and Experimental Design)
The current "emitted" from the photoemission surface can be suitably “braked” up to be stopped by a suitable contrary voltage (potential arrest), capable of preventing the electrons to reach the opposite polarity of the emissive device.
• Discussing with the students on the modality of the of the apparatus structure.
• Finding the best selection and sequence of filters, diaphragms and positioning in the optical bench.
• Developing the experimental apparatus
3 nd Learning Activity (experimental activity)
Measuring the potential stop for the different colored filters:
1. Development of the experience: changing the generator opposite voltage and bringing the index calibration of the micro-ammeter connected to the "0", it can be easily identified with the aid of a milliammeter V a .
2. Tracing the course of the current as a function of the potential difference.
4 nd Learning Activity (discussion and conclusion)
1. Students draw the characteristic curve of the color filters and using Excel determines the equation of the linear part.
2. With the calculation made the students are able to determine the experimental value of Planck's constant.
3. For each value of h the student calculates the percentage of error.
The resetting of the micro ammeter is tied to the value of the potential (V a ) which corresponds to the voltage for which the electrons are able to recombine with "holes” in the valence band. Experimentally, in order to determine the value of this potential, students proceed with a fine calibration of the generator, which is capable to reset the measure of the micro ammeter.
Then the experimental value of h is compared to the one present in the scientific literature.
2. Experimental Design
One of the methods to measure the Planck constant is to derive the voltage-current characteristic curve for a series of different color LEDs.
The method uses the energy emitted when a photon is produced as shown in Figure 1
- PPT PowerPoint Slide
- PNG Larger image(png format)
- NEW View larger figure in new window
- NEXT View next figure
- PREV View previous figure
The diode LED, as all the diodes, is a semiconductor device [ 2 ] , which behaves as a bulb lighting up when connected to a voltage generator. LED’s emit light only when the voltage is forward biased and above a minimum threshold value. Above the threshold, value the current increases exponentially with voltage. The radiated energy can derive experimentally from the characteristic curve of the diode. Therefore, we can observe that each LED is a "non-ohmic conductor", because the voltage-current relation does not follow Ohm's law of direct proportionality.
Figure 2 shows the characteristic curve of a LED. As can be seen from the figure up to a certain voltage value (V<Vg) the LED does not conduct, then for higher voltages (V>Vg) the LED begins to conduct and to emit light. To determine the value of Vg is necessary to make a linear fit of the linear part of the curve and calculate the point where this line intercepts the x-axis. We obtain a value of voltage ( V g ) which, multiplied by the electron charge (e = 1.602x10 -19 C), gives us precisely the energy of the emitted photons ( E g = eV g ).
The equation of the linear part obtained using Excel is:
(2) |
With the calculation performed with Excel software, we can determine the experimental value of Planck's constant. Starting from
And finally
And setting I = 0
And all the same time
we determine
(3) |
Using a particular device (photo emissive surface K), the interpretation of the photoelectric effect is based on a very simple and intuitive relation:
(4) |
where E i is the energy of the incident photon, L the extraction work of the electron from the metal and K e the kinetic energy of the electron released.
This relation, explaining the magnitudes, can be rewritten in the following way:
(5) |
At this point, by applying a d.d.p. as to have the polarities reversed: cathode → surface photoemission cathode and anode → collector, the electrons are clearly slowed and, acting on the micro ammeter potentiometer, you can go up to block the emitted electron flow (current). This d.d.p. takes the name of potential stop ( V a ), and then Eq. 4 becomes:
(6) |
If this operation was repeated for two different radiation accidents, the result would be:
and subtracting member to member:
up to obtain:
(7) |
The apparatus used in this experiment is shown in Figure 3 and is composed by:
• Power supply
• Diode bridge
• LED system
• Two Multimeters: one to be used as voltmeter and the other as an ammeter
The power supply is used to put in operation with the main power supply all equipment that cannot be connected directly to the 220V socket.
The diode bridge is used to convert an AC power signal into a signal in continuous energy.
The circuit that was used to experimentally determine Planck's constant is illustrated below (Figure 4):
The apparatus used in this experiment is shown in Figure 5:
The apparatus used for the measurements consisting of:
1. Optical Bench (Figure 5)
3. Photo emissive Surface
A voltage source, a measuring amplifier and a digital multimeter to use as a micro-ammeter to determine the resetting of the current.
The method represented therefore is based on the photoelectric effect use: an incident electromagnetic radiation, which strikes a metal photoemission surface, if equipped with a particular frequency (energy), can emit electrons to the previously mentioned surface. These electrons can be detected in the form of current. (Figure 6)
The experimental measurements are summarized in Table 1 .
The results using the equations 2 and 3 are summarized in Table 2 ,
Table 1. Measurements of LEDs
- NEW View table in a new window
- NEXT View next table
Here we reported in the graph the linear part for one of the four LEDs: red (Figure 7)
Table 2. Values of h
- PREV View previous table
The equation obtained with Excel is I F = 0.77V F - 1.36.
For I = 0 we obtain
and consequently
A similar behaviour is obtained for all other coloured leds.
The resulting measurements are summarized in Table 3 .
Table 3. Data of Potential Arrest
Table 3 represents the data relating to the different values of the potential shutdown. For each filter, ten measures have been taken. The students, with the help of a spreadsheet, have arranged to iterate the calculation of h as identified by the equation 5. For example, by referring to the two filters, blue and green, the relative potentials of arrest were inserted into the equation above, and by using the tabulated value of their frequencies together with the one of the electron charge, the result is:
Figure 8 presents the graph on the averages course of the arrest potentials measures, related to the specific frequencies of incident radiation.
4. Discussion
For each values obtained of h has been calculated the percentage error as
The experimental value of h is compared to the one present in the scientific literature. In Table 4 , h measured values are confronted.
Table 4. Comparison of the values of h calculated by using the two methods
For what concerns the limits connected to the two methods, it can be easily said that the major problem is related to errors in the potential measurement, which is obtained by extrapolating the linear part of the curve of one LED and the same potential arrest measurement. Since, however, the purpose of the work appears to have definitely educational aspects, what is relevant though, beyond acceptable values, is the order of magnitude of the measures, which is still respected.
5. Conclusions
Within the framework of a master on the Didactics of Science, the authors respectively a chemist and a physicist offer their students two different ways to measure the Planck’s constant: as measurement of the energy of the photons emitted by LEDs diode and the study of the photoelectric effect induced by the light emitted from a mercury lamp.
The authors, involved students by using the IBSE methodology in a series of activities of observation, exploration, construction of circuits, adjustment of a optical bench, use of computer equipment, data processing, analysis of the errors, which allowed them to acquire an experimental mode to calculate the Planck constant.
In the first method, the value of Planck's constant has been determined through current-voltage measurements. The mean value obtained is within the limits of experimental error and in good agreement with the value of literature, considering the available experimental apparatus.
The light emission of the LED starts from a value of potential ( V g ) that corresponds to the voltage for which the electrons are able to recombine with “holes” of the valence band.
In the second method, the mean value is obtained by h single values measured in relation to the confrontation among all the different filters: Blue - Green, Blue – Yellow and Green – Yellow. The arrest potentials used are those of the mean values measured in Table 2 . Even in this case, the mean value obtained is within the limits of experimental error and in good agreement with the value of literature, considering the available experimental apparatus.
Acknowledgements
Andrea Checchetti thanks Giovanni Orlando from I.I.S. “Eleonora Pimentel” of San Giovanni in Fiore (Italy) for his help. Alessandro Fantini thanks prof. Luigi A. Macrì for his contribution.
The authors thanks Dr. Gabriella Fantini (Italy) and prof. Donato Martano for their help throughout the translation.
The Institute of Higher Education “Eleonora Pimentel” of San Giovanni in Fiore (Italy) and the Scientific Lyceum “Enrico Fermi” of Catanzaro Lido (Italy) supported this work.
[1] | Bell, T. Urhahne, D., Schanze, S. & Ploetzner, R., (2010) Collaborative Inquiry learning: Models, tools and challenges, International Journal of science education, 32(3), pp. 349-377. | ||
[2] | Maria Rute de Amorim e Sá Ferreira André and Paulo Sérgio de Brito André, “Classroom fundamentals: measuring the Planck constant”, online available on Science in School, https://www.scienceinschool.org/2014/issue28/planck. | ||
[3] | Cloninger, T. Zhou, F. “Computer-Based Experiment for Determining Planck's constant Using LED's” The Physics Teacher. 46. (2008): 413-415. | ||
[4] | Raymond A. Serway “Physics for Scientists and Engineers” S.E.S. (1986): 557-560. | ||
[5] | David Halliday, Robert Resnick “Fisica” C.ed. Ambrosiana (1966): 591-595. | ||
- Full-Text PDF
- Full-Text ePUB
- Citation-(RIS Format)
- Citation-(BibTeX Format)
- Citation-(EndNote Format)
- Conferences
- Special Issues
- Google Scholar
- VIRAL HEPATITIS CONGRESS
- JournalTOCs
Help & Contacts
- Questionnaire
IMAGES
VIDEO
COMMENTS
Determination of Planck's constant using LEDs The purpose of this lab activity is to determine Planck's constant by measuring the turn-on voltage of several LEDs 1. Introduction Light-emitting diodes (LEDs) convert electrical energy into light energy.
11. Determination of Planck's con-stant
Adapted from a lab procedure written by Martin Hackworth, University of Idaho Objective: Scientists use Planck's constant (h) frequently. In this experiment, you make will measure the emission wavelength and turn-on voltages of several light-emitting diodes (LEDs) in order to determine the numerical value of Planck's constant.
In this experiment you will measure the numerical value of Planck's constant h using an LED and a diffraction grating.
Theory Planck’s constant (h), a physical constant was introduced by German physicist named Max Planck in 1900. The significance of Planck’s constant is that â€ËÅ"quanta’ (small packets of energy) can be determined by frequency of radiation and Planckà...
The write-up for this experiment is copied from the manual which came with the ESCO LED Planck's constant determination apparaturs.
All Lab Experiments 55.9K subscribers 1.4K 80K views 3 years ago Modern Physics Lab & Viva Determination of Planck's Constant using LED is the experiment covered by this video. ...more
3 The Experiment We employ light emitting diodes (LEDs) to determine Planck's constant. The basic idea in this measurement is that the photon energy given by E = hν is equal to the energy gap Eg between the valence and conduction bands of the diode.
In this experiment your goal is to measure Planck's constant using a collection of light emitting diodes (LEDs). You will have two weeks in which to build and perform this experiment. Your report is due at the beginning of lab on 2007-01-30.
This document describes an experiment to determine Planck's constant using light emitting diodes (LEDs). It explains that LEDs emit photons of a specific wavelength when a current is applied, and that the minimum voltage required for emission is called the threshold voltage. It then outlines the relationships between the threshold voltage, band gap energy of the semiconductor, and the photon ...
The relationship between the wavelength of the emitted photon, the applied potential and discrete quanta of energy E is: hc E = hf = = e V he discrete step in applied voltage over the LED. The experimental determination of Planck's constant is then easily ob-tained by determining the wavelength of the emitted radiation from an LED and appl
For determination of Planck's Constant and work function: Insert the red color filter (635nm), set light intensity switch (12) at strong light, voltage direction switch (16) at '-', display mode switch (10) at current display. Adjust to de-accelerating voltage to 0 V and set current multiplier (4) at X0.001.
Abstract The key parameter for determination of Planck's constant using LED is the voltage required to turn on an LED. Many experiments have been used a voltmeter to measure the voltage. The accuracy of voltage obtained depends on experience of experimenter in deciding when the LED stared to emit.
This video describes how the value of Planck's constant can be evaluated using I-V characteristics of different LEDs
The document describes an experiment to determine Planck's constant using LEDs. LEDs emit photons when forward biased with energy equal to the voltage times the electronic charge. Plotting knee voltage vs inverse wavelength for different colored LEDs yields a straight line, and the slope equals Planck's constant divided by the speed of light. Experimental procedures, an observation table, and ...
Corresponding voltage across the LED is measured using a voltmeter,which is the knee voltage. Repeat, by changing the LED and note down the corresponding knee voltage. Using the formula given,find the value of the Planck's constant.
This video demonstrates an #Experiment on measuring Planck's constant using LED. #PlancksConstantUsingLEDTo determine the Plancks constant using LED, one nee...
Experimental determination of Planck's constant h = 6:626u00021034Ju0001 s is performed using Light Emitting Diodes (LEDs). Spectropho- tometry and basic circuit analysis techniques are employed to obtain empirical data with respect to the energy of the emitted photons of light and thus used to calculated Planck's constant.
If you want to determine the value of Planck's Constant using LED. Here is just a little modification in the calculations. Rest experiment is the same.
The aim of this experiment was to utilize the Inquiry Based Science Education, (IBSE) in order to offer the students a better understanding of the light-matter interaction. The inquiry-based teaching addresses the question of how the students make observations, develop hypotheses about phenomena, and devise tests to investigate their hypotheses. Using IBSE they share responsibility within the ...
Reeja G.NairAssistant Professor Department of PhysicsGovernment College Malappuram
PLANKS CONSTANT experiment - Free download as PDF File (.pdf), Text File (.txt) or read online for free. This document describes a procedure to determine Planck's constant using LEDs of different colors. LEDs of red, yellow, blue and violet colors are used. The activation voltage and current through each LED is measured by varying the voltage from 0-3V. Graphs of current vs voltage are plotted ...